• Accident Investigations: Vehicle Lamp Examinations

    June 17, 2017 | Blog | rci
  • Accident Investigations

    As part of an accident investigation, the question of whether the vehicle’s lights were on or not can be an important issue. Did the car have its headlights on at night? Did the driver use the turn signal before making his turn? Did your client see the brakes lights of the car stopping for traffic? Many times, the proper examination of the vehicle’s lights can answer these questions and be a deciding factor in determining fault.
    Vehicle lamp examination as part of a traffic crash investigation can be accomplished if the examination is conducted properly and the lamp is collected in a manner that will cause no damage. Vehicle lamp examinations are commonly completed where there are discrepancies regarding the status of the vehicle’s lights.
    Vehicle Lamp Design
    Vehicle lamps are all designed in the same basic manner. A sealed beam lamp will consist of a glass envelope containing an inert gas. An inert gas is chemically inactive and will not react with anything.
    The glass bulb is attached and sealed to a base. On the base, an investigator will typically find the trade number and manufacturer of the lamp as well as the contact lug pin. These items should be noted by the investigator examining the bulb.
    Inside the glass bulbs are filament terminal supports, usually made of steel, and encased in an insulator. The filament is crimped or clamped to the ends of the support. The filament is usually made of tungsten and is coiled into a series of loops, evenly spaced throughout the length of the filament.
    When the lamp is in a stage of incandescence, an electrical current is passed through the filament which raises the temperature to the point it glows. This can produce a temperature up to 4,000°F. The filament becomes soft and susceptible to deformation.
    Vehicle Lamp Examination
    The first step an investigator must complete in a vehicle lamp examination is to ensure the lamp is not inadvertently damaged or destroyed before it can be examined. If the lamp is still attached to the vehicle, it should be carefully removed and packaged as evidence using standard evidence collection procedures and in a manner that loose parts, such as the filament, cannot be lost.
    The examination should start with recording the identifying information of the bulb. The best method is using a form specifically designed for this purpose. These forms can be either be produced by the investigator or there are several forms that can be copied or downloaded.
    The examination of the lamp should be completed under a microscope or other magnifying object and, as in all evidence examination, the lamp should be photographed, from various angles and perspectives, and detailed notes of the examination procedure should be completed.
    When the filament is hot, the temperature can be in excess of several thousand degrees Fahrenheit. With the filament at these temperatures, it becomes soft. If the glass bulb stays intact during an impact, a filament that was incandescent will stretch and coil indicating it was on during the impact. This distortion of the filament is called “hot shock” and can be classified as major distortion. Minor distortion, slightly bowed or curved filament, is caused by the age of the lamp (called “age-sag”) or during the manufacture of the lamp. Minor distortion will still display uniform spacing of the filament coils.
    If the glass bulb is broken and air is allowed to contact the incandescent filament, then the glass can melt and fuse to the filament. On occasion, this fused glass will form small beads of melted glass on the filament that sometimes will require a magnifying device to see. When air contacts the stem and support posts, the oxygen will react with the hot post and stem and “oxidation” will occur. This is evidenced by a while or yellowish power that will form on the filament or the stem/posts.
    If the filament is cold or is not incandescent, then there will be no stretching of the filament. If the filament breaks, it will fracture, not stretch. At times, pieces of the filament can be found inside the glass bulb. If the glass bulb breaks and oxygen enters the space, making contact with the filament and stem/posts, there will be no oxidation as the components are not hot and will not oxidize with the air entering the space. During “cold shock””, the filament will display damage in the form of clean, sharp breaks.
    If there are reports of the vehicle lamps being on, but dim, then the investigator must consider the possibility of a mechanical issue. Lamps need electrical current to illuminate. A low illumination of a lamp will most likely be caused by a fault in the electrical system. The most common issue involved is the alternator of the vehicle which converts mechanical energy to electrical energy. If a faulty alternator is suspected, then the investigator must have it inspected and tested by a qualified mechanic.

Submit your review
1
2
3
4
5
Submit
     
Cancel

Create your own review

Average rating:  
 21 reviews
by Ms. Walli on blog
Top Notch, Effective Process Service

I was referred to Anthony DiMario by another process server who did not operate in my area. For weeks, I had been trying to serve a time-sensitive mandatory notice on a pair of elusive tenants. RCI was attentive and responsive to the specific nature of my request. Anthony skillfully stepped in and, within the first 24 hours (on a weekend, too), delivered the utmost professional results. Thanks for helping to remove the worry of missing a deadline! I highly recommend this company for their efficiency, effectiveness and integrity.

by Michael Rosofsky - Attorney at Law (443) 275-0506 on blog
Best Service & Reasonable prices!

Best in the business and reasonable prices too.

by Jeremiah Arbogast on blog
Baltimore's Best!

Always a pleasure to do business with. We work together to get out of area Service of Process completed professionally.

by Souza LLC on blog
Nobody is Better

RCI is easily the best process service that we have used in the last 10 years. Fast, reliable and competitively priced. Thanks a million!!

by Linda F. Burgos on blog
Excellent Service & Rates

I am very happy with the fast and professional service, and reasonable rates provided by the staff at RCI.

Page 1 of 5:
«
 
 
1
2
3
4
5
 
»